Most Wi-Fi pairing failures stem from minor operational missteps, router configurations, or network credential mismatches. By following this structured guide in order, you can typically resolve the issue without further assistance.
Phase 1: Diagnose the Robot’s Status (Indicator Lights)
Before troubleshooting, check the robot’s panel indicator light to understand its current state:
- Slow blinking white light (approx. 1.5s cycle): The robot is in pairing mode. You may proceed with the App setup.
- Fast blinking red light (3 times): Network connection failed (Event Code: N212).
- Solid red light: Abnormal panel status, which may indicate a hardware issue.
- No light: The robot is powered off, or the battery is critically low. Please charge it for at least 2 hours before trying again.
Phase 2: Pre-Configuration Checklist
Ensure both your phone and router are optimally configured before attempting to pair.
2.1 Phone Settings
- App & Permissions: Ensure the TerraMow App is updated to the latest version. Enable Location/GPS permissions. (For iPhone users: Also enable "Local Network" and "Location" permissions for the TerraMow App in iOS Settings).
- Network State: Temporarily disable mobile data (4G/5G), VPNs, and any active firewalls.
- Wi-Fi & Bluetooth: Connect your phone to your home Wi-Fi and verify internet access. Then, toggle both Bluetooth and Wi-Fi off, wait 30 seconds, and turn them back on.
2.2 Router Settings
- Security Protocols: Enable WPA / WPA2. Disable WEP, WPA3, passwordless authentication, guest mode, and any MAC address whitelisting/firewalls.
- Credential Format: Ensure your Wi-Fi name (SSID) and password contain only English letters and numbers (no special characters or hidden spaces). Pay strict attention to case sensitivity.
- Dual-Band Separation: If your 2.4 GHz and 5 GHz networks share the same name, the robot may experience interference or repeated dropouts. We highly recommend splitting them into two distinct SSIDs (e.g., TerraMow-2.4G and TerraMow-5G) and connecting the robot to the 5 GHz network.
- Capacity & Restrictions: Ensure the router has not reached its maximum device limit and is not set to "reject weak signal connections."
- Unsupported Networks: Captive portal networks requiring web authentication (e.g., hotels, airports) are not supported.
- Action: Reboot your router before proceeding.
Phase 3: Step-by-Step Reconfiguration
- Optimal Placement: Move the robot main unit only (the base station is not needed) close to the router to ensure a strong signal during setup.
- Power Cycle: Turn off the robot, wait 10–30 seconds, and turn it back on.
- Enter Pairing Mode: Press and hold the Power and Home buttons simultaneously for 2 to 3 seconds. Release them only when you hear the voice prompt "Wi-Fi connection has been reset" and the indicator light begins to blink white slowly.
-
App Pairing: Keep your phone within 1.5 meters (up to 3 meters max) of the robot with minimal physical obstacles. Tap "+" (Add Device) in the TerraMow App and follow the wizard. For a step-by-step tutorial, click here to learn more.💡 Tip: Manually type the Wi-Fi name and password. Do not rely on your phone’s auto-fill feature to avoid hidden spaces or case-sensitivity errors.
Phase 4: Alternative Methods & Factory Reset
If standard pairing fails, try these advanced methods:
4.1 Hotspot Configuration Method
- In the App, tap "Try other ways" → "Go to settings".
- Go to your phone’s system Wi-Fi settings and connect to the robot’s temporary hotspot (named TerraMow-xxx, no password required).
-
Return to the TerraMow App to input your home Wi-Fi credentials.
- (Android Users): If a "WLAN has no internet" dialog pops up, select "Do not switch", "Do not allow", or "Use" to stay connected to the robot.
- (iPhone Users sharing a hotspot): Ensure "Maximize Compatibility" is enabled on the hotspot-providing device.
- The configuration is only successful when you see that "Wi-Fi connected successfully". Afterwards, manually reconnect your phone to your home Wi-Fi.
4.2 Factory Reset (Last Resort)
If all else fails, press and hold the Start and Power buttons on the top panel for 5 seconds.
⚠️ Warning: This will permanently erase all saved Wi-Fi networks, map data, no-go zones, and scheduled cleaning settings. Use only when necessary.
Phase 5: Still Not Working? (Escalation)
If you have completed all steps above and the robot still cannot connect, please submit a feedback report via the App. The required information depends on the indicator light:
- If the white light is blinking slowly (Pairing mode is normal): Submit feedback, click to upload all logs, and provide your router’s model number and configuration page screenshots for our engineering team to analyze.
-
If the red light is solid (Abnormal status): Submit feedback, upload all logs, and attach a short video of the robot’s behavior to help us diagnose potential hardware issues.